How to Use BBLUNT Hot Shot Hold Spray for Instant Firm Hold Correctly

BBLUNT Hot Shot Hold Spray is a firm-hold finishing spray from the BBLUNT hair colour and styling range that locks styles in place instantly while leaving the hair looking natural, not stiff or coated. Whether the look is a sleek blowout, a textured wave set, a twist-out, or an updo, the Hold Spray sets the shape and controls flyaways without the crispy finish that heavier styling sprays can leave behind. The 300 ml bottle is NABL tested and patch tested, and this guide walks through the complete application process as well as how to get the best hold from each use.

Before You Begin

A few steps before spraying make a significant difference to how long the hold lasts and how natural the result looks.

• Finish the style completely before spraying. Hot Shot Hold Spray locks the hair in the position it is in when applied. Shape, smooth, and set the look exactly as you want it before picking up the can.
• Start on dry hair. Spraying over wet or damp sections dilutes the hold polymer before it can film-form properly. Blow dry or allow the hair to dry fully before applying.
• Shake the can gently before use. A gentle shake redistributes the propellant and formula so the spray comes out as a fine, even mist from the first burst.
• Apply a heat protectant before any heat styling. Hot Shot Hold Spray is applied after the style is finished. If heat tools are part of the look, apply a dedicated heat protectant before blow drying or using a straightener or curling tong, then use the Hold Spray once the hair has cooled and the style is set.
• Work in a well-ventilated space. Aerosol hair sprays should be used in a ventilated room. Avoid spraying near open flames or heat sources, as the product is aerosol-based.

How To Use: Step by Step

1. Complete and set the style on dry hair Blow dry, straighten, curl, or air dry the hair into the finished look before reaching for the Hold Spray. Smooth down flyaways with your hands or a fine-tooth comb. Arrange partings, pin sections if needed, and make sure the style is exactly where you want it before spraying.
2. Shake the can gently Give the can a gentle shake for a few seconds to ensure the formula is well mixed and the spray nozzle delivers a consistent fine mist from the start.
3. Hold the can 25 to 30 cm from the hair Position the can about 25 to 30 cm (10 to 12 inches) away from the surface of the hair. This distance produces a fine, diffused mist that covers evenly. Holding too close concentrates the product and creates wet, heavy patches that can make the hair stiff or clumped. Holding too far weakens the hold and wastes product.
4. Spray in short, even bursts over the finished style Use two to three short bursts, moving the can in a sweeping motion across the full surface of the style. Cover the top, sides, and any sections prone to lifting or frizzing. Avoid holding the nozzle in one spot, as concentrated application in a single area creates build-up and stiffness.
5. Allow the spray to dry fully before touching Leave the hair undisturbed for 30 to 60 seconds after spraying to allow the hold polymers to dry and set. Touching, combing, or brushing the hair while the spray is still wet can disturb the style before it has locked in place.
6. Add a second layer only if more hold is needed Assess the hold once the first application has dried. For styles that need extra staying power in humid conditions or through a long day, a second light burst from the same distance adds hold without building up stiffness. Allow the second layer to dry fully as well.
7. Use a targeted spray for touch-ups through the day For a mid-day refresh, direct a single short burst at the sections where hold has relaxed or flyaways have appeared. This spot-fix approach is more effective than re-spraying the entire style and avoids over-layering product.

Best Uses for Hot Shot Hold Spray

Hot Shot Hold Spray is versatile enough to work as the finishing step for most styles, but it works best in a few specific ways.

• Blowouts and straight styles: Mist lightly over a finished blowout to keep the hair smooth and lying flat. The spray seals the cuticle and stops humidity from causing frizz to rebuild through the day.
• Updos and pinned styles: A mist over the outer layer of a bun, chignon, or french twist keeps stray hairs from pulling out and the edges from lifting. For voluminous updos, a mist under sections helps hold them without flattening the shape.
• Waves and curls: A light finish mist over defined waves or curls sets the shape without disrupting the texture. Apply with fingers spread rather than raking through, and spray from above rather than pointing directly at individual curls to keep them intact.
• Slicked-back and precision styles: For sleek styles where every hair needs to stay in place, the firm hold level keeps even short pieces flat along the edge. Apply to already gelled or pomaded sections for a clean, polished finish that lasts.
• Frizz control: A light all-over mist on humid days gives a protective layer that slows moisture absorption and keeps the style from expanding at the mid-lengths and ends.

Keeping the Hold Without Build-Up

Hold sprays used regularly can accumulate on the hair if not properly washed out, which makes the hair look dull, feel heavy, and respond less well to the product over time. A few simple habits prevent this.

• Wash the hair thoroughly at the end of each day of heavy styling product use. A good lather and full rinse removes the hold film left by the spray.
• Use a clarifying or deep-cleansing shampoo once a week if styling products are used daily. A clarifying wash removes cumulative build-up that regular shampoos miss, keeping the hair light and responsive.
• Avoid layering multiple strong-hold products on the same sections. If a gel, mousse, or pomade is already in the hair, a light finishing mist is sufficient. Stacking multiple firm-hold products concentrates build-up on the same hair.
• Apply the Hold Spray on the outer surface of the style rather than close to the roots unless the scalp area needs specific hold. Root application increases the rate of build-up and can make fine hair look flat faster.

The Product

Conclusion

BBLUNT Hot Shot Hold Spray gives instant, firm hold on a finished style without leaving the hair stiff or coated. Apply it as the last step on dry, styled hair, hold the can 25 to 30 cm away, and use short sweeping bursts to cover the style evenly. Allow each layer to dry before assessing whether a second application is needed. Used correctly, the Hold Spray keeps styles in place through a full day while washing out cleanly at the end of it.

FAQs