Bond Repair Shampoo: NABL Lab Test Report
NABL lab test report for Bond Repair Shampoo: heavy metals not detected, pathogens absent and pH 5.89. Batch AM5B085.
Safety Summary: Bond Repair Shampoo
Is Bond Repair Shampoo safe? Yes. It was independently tested at Sigma Test & Research Centre, a laboratory accredited by NABL (Accreditation No. TC-15193). The tested sample, from batch AM5B085, met every safety limit the laboratory checked.
Free from lead and arsenic. The report found no detectable lead or arsenic - both were below the laboratory's detection limit of 0.25 mg/kg.
Free from harmful bacteria and fungi. Four organisms were tested: Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus and Candida albicans. All were reported Absent. Total microbial count was Less than 10 cfu/gm (limit 1000 cfu/gm); Total yeast & mould count was Less than 10 cfu/gm (limit 100 cfu/gm).
Gentle, hair-friendly pH. The measured pH is 5.89, which is mildly acidic. The standard allows 4.0 - 9.0 for this product type.
Sulphate-free and paraben-free. The published ingredient list contains no sulphates, parabens or mineral oil. It cleanses using milder amino-acid surfactants - sodium lauroyl sarcosinate, cocamidopropyl betaine and sodium cocoyl isethionate. Preservation uses phenoxyethanol, ethylhexylglycerin and sodium benzoate.
Is it chemical free? No cosmetic is chemical-free - water itself is a chemical. This one is free from sulphates, parabens, mineral oil and any detectable lead or arsenic.
What these results cover. The laboratory findings apply to the tested sample from batch AM5B085 and the parameters listed on this page. Skin tolerance is assessed separately, in the dermatological patch test certificate. NABL accredits laboratories, not products.
Key Findings at a Glance
Results of Analysis
Result is the measured outcome for this batch. Requirement / Limit is the specification where the standard defines one; a dash means it defines none. Test Method is the standard the laboratory followed.
| Parameter | Result | Requirement / Limit | Test Method |
|---|---|---|---|
| Physical & Organoleptic | |||
| Appearance | White viscous liquid | - | STRC/STP/F256 |
| Colour | White | - | STRC/STP/F256 |
| Odour | Characteristic | - | STRC/STP/P044 |
| Chemical Parameters | |||
| pH | 5.89 | 4.0 - 9.0 | IS:7884:2004 |
| Foam height for 2% solution, mm | 168 | min 150.0 | IS:7884:2004 |
| Active detergent content, % w/w | Nil | - | STRC/STP/P020 |
| Viscosity (Temp:25.6C,RPM:25,SPL No:L3,Torque:76.3%) cps | 8963 | - | Indian Pharmacopoeia 2022 |
| Specific gravity | 1.025 | - | STRC/STP/P060 |
| Heavy Metals | |||
| Lead (as Pb), mg/kg | Not Detected (DL 0.25) | - | STRC/STP/P018 |
| Arsenic (as As), mg/kg | Not Detected (DL 0.25) | - | STRC/STP/P018 |
| Microbial Counts | |||
| Total microbial count, cfu/gm | Less than 10 | NMT 1000 | IS:14648:2011 |
| Total yeast & mould count, cfu/gm | Less than 10 | NMT 100 | IS:14648:2011 |
| Pathogens | |||
| Escherichia coli, per gm | Absent | - | IS:14648:2011 |
| Pseudomonas aeruginosa, per gm | Absent | - | IS:14648:2011 |
| Staphylococcus aureus, per gm | Absent | - | IS:14648:2011 |
| Candida albicans, per gm | Absent | - | IS:14648:2011 |
Understanding These Tests for Bond Repair Shampoo
Physical & Organoleptic
On the tested sample, Bond Repair Shampoo was recorded as a white viscous liquid, white in colour and with a characteristic odour.
These checks record what the laboratory observed in the sample as received.
Chemical Parameters
Bond Repair Shampoo recorded pH 5.89 against a requirement of 4.0 - 9.0 and foam height for 2% solution 168 mm against a minimum of 150.0 mm. It also lists active detergent content Nil, viscosity 8963 cps and specific gravity 1.025, for which the standard sets no specification.
Chemical parameters are measured against the standard's specification where one exists.
Heavy Metals
In this report, Bond Repair Shampoo showed no detectable lead or arsenic - each below the laboratory's detection limit of 0.25 mg/kg.
Heavy metals can enter a product through raw materials or manufacturing.
Microbial Counts
Bond Repair Shampoo recorded total microbial count Less than 10 cfu/gm against a limit of NMT 1000 cfu/gm and total yeast & mould count Less than 10 cfu/gm against a limit of NMT 100 cfu/gm.
These tests count viable microorganisms against the limits set by the standard.
Pathogens
In the tested sample of Bond Repair Shampoo, Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus and Candida albicans were reported Absent - not detected in the tested quantity.
Pathogen tests cover only the organisms listed, not all microorganisms.
Test Overview
| Report Title | Chemical and Microbiological Analysis - Bond Repair Shampoo |
| Parameters Measured | physical and organoleptic properties, chemical parameters, heavy metals, microbial counts and pathogens |
| Test Type | Laboratory chemical and microbiological analysis of a product sample |
| Test Methods | IS:7884:2004; Indian Pharmacopoeia 2022; IS:14648:2011 |
| Sample Tested | AM5B085 (300 ml x 1) |
About Bond Repair Shampoo
Hair that steals the spotlight? That's a Bond Girl's true partner-in-crime - BBlunt Bond Repair Shampoo. The undercover agent rescues, restores & rejuvenates locks with unstoppable finesse. Enriched with the groundbreaking MailPeptide BondTech, this shampoo isn't just another agent-it's your mane's MI6. It eliminat
Claims and Their Evidence
Lab-sourced rows are measured results. Product-page rows are the brand's own claims, shown with the brand's qualifier. The laboratory report is not evidence for cosmetic-benefit claims.
| Statement | Evidence / basis | Source |
|---|---|---|
| pH within the specified range | Measured pH 5.89, within the 4.0 - 9.0 requirement. | Lab report 13033896/A |
| Foaming meets the standard | Foam height 168 mm against a minimum of 150.0 mm. | Lab report 13033896/A |
| No detectable heavy metals | Lead and Arsenic reported Not Detected at a detection limit of 0.25 mg/kg. | Lab report 13033896/A |
| Within microbiological limits | Counts within the standard limits; specified pathogens reported Absent. | Lab report 13033896/B |
| Sulphate-free cleansing base | Formulated with sodium lauroyl sarcosinate, cocamidopropyl betaine and sodium cocoyl isethionate in place of SLS/SLES. | Product ingredient list |
| Paraben-free | No parabens in the published ingredient list. | Product ingredient list |
Report Details
| Testing Laboratory | Sigma Test & Research Centre (NABL-accredited, Accreditation No. TC-15193) |
| ULR Number | TC1519325000001529F |
| Report No. | 13033896/A, 13033896/B |
| Report Issue Date | 08/03/2025 |
| Testing Period | 25/02/2025 to 04/03/2025 |
| Batch Tested | AM5B085 (Mfg. 02/2025; use before 24 months) |
| Standards Referenced | IS:7884:2004; Indian Pharmacopoeia 2022; IS:14648:2011 |
| Authorised Signatory | Shruti Vij, Technical Manager, Sigma Test & Research Centre |
What This Report Shows
What the results demonstrate
- Physical characteristics of the tested sample were recorded as observed by the laboratory.
- Measured chemical parameters that carry a specification fell within the referenced limits.
- The listed heavy metals were below the laboratory's detection limit in the tested sample.
- The tested sample met the microbiological count limits of the referenced standard.
- The specified pathogenic microorganisms were reported Absent in the tested sample.
- Testing was performed by an NABL-accredited laboratory.
What the results do not demonstrate
- They do not certify the product; NABL accredits laboratories, not products.
- They do not establish overall safety or suitability for every individual.
- They do not prove any cosmetic-benefit or performance claim; those are addressed separately and on the product page.
- They do not cover parameters or organisms outside those listed.
- They apply to the tested sample from the stated batch, not necessarily to other batches.
Formulation at a Glance
From the ingredient list published on the product page. Not part of the laboratory report.
Cleansing System
| Component | Role in the formulation |
|---|---|
| Sodium Lauroyl Sarcosinate | Amino-acid-based surfactant used in place of sulphates. |
| Cocamidopropyl Betaine | Mild coconut-derived surfactant for gentle cleansing and foam. |
| Sodium Cocoyl Isethionate | Mild surfactant that builds lather while staying gentle. |
Active Ingredients
| Component | Role in the formulation |
|---|---|
| Xylitylglucoside | Sugar-derived humectant, part of a moisturising complex. |
| Anhydroxylitol | Sugar-alcohol humectant supporting surface hydration. |
| Hyaluronic Acid | Humectant that binds water in the upper skin layers. |
| Panthenol (Vitamin B5) | Pro-vitamin B5 humectant supporting moisture and elasticity. |
Moisturising and Emollient
| Component | Role in the formulation |
|---|---|
| Glycerin | Humectant that draws water into the skin surface. |
Conditioning Agents
| Component | Role in the formulation |
|---|---|
| Amodimethicone | Silicone that smooths the surface and adds slip. |
Texture and Stability
| Component | Role in the formulation |
|---|---|
| Aqua (Water) | Solvent base of the formulation. |
| Acrylates Copolymer | Polymer used to thicken or form films. |
| Citric Acid | Adjusts the pH of the formulation. |
| Disodium EDTA | Chelating agent that stabilises the formula against metal ions. |
Preservative System
| Component | Role in the formulation |
|---|---|
| Phenoxyethanol | Broad-spectrum preservative used at low levels. |
| Sodium Benzoate | Preservative effective in acidic formulations. |
What the Formulation Leaves Out
| Excluded | Basis |
|---|---|
| No sulphates | Not present in the published ingredient list. |
| No parabens | Not present in the published ingredient list. |
| No mineral oil | Not present in the published ingredient list. |
Published Research on Key Actives
Published literature on each ingredient, not studies on this product.
| Ingredient | Published finding | Relevance to the formulation |
|---|---|---|
| Hyaluronic Acid | Hyaluronic acid is documented as a key water-binding molecule in skin hydration (Papakonstantinou E, et al. Dermatoendocrinol. 2012;4(3):253-258). | Supports hyaluronic acid or sodium hyaluronate as a hydrating agent. |
| Panthenol (Pro-Vitamin B5) | Topical dexpanthenol is documented to support hydration and barrier function (Proksch E, et al. Am J Clin Dermatol. 2009;10(6):359-367). | Supports panthenol for moisture retention and elasticity. |
Dermatological Patch Test Certificate
This NABL lab test report covers the chemical and microbiological analysis of Bond Repair Shampoo. Skin tolerance is a separate question, assessed through dermatological patch testing. The dermatological patch test certificate for this product is published on its own page, so you can review the laboratory analysis here and the patch-test findings there as one trust cluster.
View the Original Lab Report
The complete original report for Bond Repair Shampoo is available as issued by the laboratory. It carries the laboratory letterhead, the ULR number, and the authorised signatory's details.
The Tested Product
Bond Repair Shampoo
The results on this page come from laboratory testing of a sample from batch AM5B085. See the complete ingredient list, current offers and reviews on the product page.
View ProductFrequently Asked Questions
A: Yes. In this report, Lead and Arsenic were reported below the laboratory's stated detection limit of 0.25 mg/kg at Sigma Test & Research Centre, an NABL-accredited laboratory (Accreditation No. TC-15193).
A: For the tested batch, microbial counts were reported within the limits of the referenced standard and the specified pathogens were reported Absent. These results indicate the tested sample met the referenced microbiological limits; they do not establish overall product safety.
A: The measured pH in this report is 5.89. The referenced standard allows 4.0 - 9.0 for this product type.
A: The published ingredient list for this product contains no sulphates, parabens or mineral oil. This is based on the ingredient list, not on the laboratory report, which covers contaminants and microbiological quality.
A: No. The report covers chemical and microbiological parameters on a sample from the stated batch. Performance and cosmetic-benefit claims are made by the brand on the product page and are not part of this laboratory report.
A: "Not Detected" means a substance was below the laboratory's stated detection limit using the specified method. "Absent" means a specified microorganism was not detected in the tested quantity using the referenced method.
A: A ULR (Unique Lab Report) number is a one-of-a-kind identifier that NABL-accredited laboratories print on every test report, making it traceable. The ULR for this report is TC1519325000001529F. The original report PDF linked on this page carries the laboratory letterhead and authorised signatory details.
A: No. NABL accredits laboratories, not products. This page reports the results of testing performed at Sigma Test & Research Centre, an NABL-accredited laboratory (Accreditation No. TC-15193) on a sample of this product. It does not represent a product certification by NABL.
A: The report covers batch AM5B085 (manufactured 02/2025). The laboratory report states the tested sample as 300 ml x 1. Results refer only to the tested sample and the parameters listed.
References
- IS:7884:2004. Bureau of Indian Standards.
- Indian Pharmacopoeia 2022. Indian Pharmacopoeia Commission.
- IS:14648:2011. Bureau of Indian Standards.
- Sigma Test & Research Centre. Test reports 13033896/A, 13033896/B.
Delete Your Account
Deleting your account will permanently remove your personal data, app activity, and any associated information. This action cannot be undone. To proceed, please verify your identity by entering your registered email address or phone number below. We’ll send you a confirmation link or code to complete your account deletion request.
